DL5WB-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL5WB-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Press*	Temp.in*	Hum*	QNH*	Temp.out*
1777237219	998.9 hPa	5.9 C deg	56.9 %	1025.1 hPa	0 C deg
1777235394	998.8 hPa	6.7 C deg	54.3 %	1025 hPa	0 C deg
1777233574	998.7 hPa	7.5 C deg	51.9 %	1024.8 hPa	0 C deg
1777229940	998.5 hPa	8.5 C deg	46.7 %	1024.5 hPa	0 C deg
1777222629	998.2 hPa	12 C deg	35 %	1023.9 hPa	0 C deg
1777218736	998.5 hPa	14 C deg	31.8 %	1023.9 hPa	0 C deg
1777216831	998.7 hPa	14.1 C deg	32.6 %	1024.1 hPa	0 C deg
1777215017	998.8 hPa	14.2 C deg	33.2 %	1024.3 hPa	0 C deg
1777213205	999 hPa	14.5 C deg	32.6 %	1024.4 hPa	0 C deg
1777211389	999 hPa	13.9 C deg	34.3 %	1024.5 hPa	0 C deg
1777209573	999.2 hPa	13.6 C deg	35.3 %	1024.8 hPa	0 C deg
1777205973	999.6 hPa	13 C deg	34.4 %	1025.2 hPa	0 C deg
1777204960	999.7 hPa	12.7 C deg	36.5 %	1025.3 hPa	0 C deg
1777201353	1000.1 hPa	22.2 C deg	22.1 %	1024.9 hPa	0 C deg
1777199516	1000.3 hPa	32.6 C deg	13.5 %	1024.3 hPa	0 C deg
1777197701	1000.4 hPa	32.4 C deg	13.8 %	1024.4 hPa	0 C deg
1777195885	1000.2 hPa	33.3 C deg	17.8 %	1024.1 hPa	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)