N0OWT-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0OWT-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	PC Board Temp*	-*
1780893144	13.7 V	28 F	0 On=255 Off=0
1780892245	13.5 V	28 F	0 On=255 Off=0
1780891345	13.5 V	28 F	0 On=255 Off=0
1780888645	13.5 V	28 F	0 On=255 Off=0
1780886845	13.7 V	28 F	0 On=255 Off=0
1780885044	13.6 V	28 F	0 On=255 Off=0
1780883246	13.5 V	28 F	0 On=255 Off=0
1780882345	13.6 V	28 F	0 On=255 Off=0
1780881444	13.6 V	27 F	0 On=255 Off=0
1780880545	13.5 V	28 F	0 On=255 Off=0
1780879646	13.5 V	28 F	0 On=255 Off=0
1780876945	13.6 V	28 F	0 On=255 Off=0
1780876044	13.7 V	28 F	0 On=255 Off=0
1780874245	13.6 V	27 F	0 On=255 Off=0
1780871545	13.5 V	28 F	0 On=255 Off=0
1780867946	13.5 V	28 F	0 On=255 Off=0
1780867045	13.5 V	28 F	0 On=255 Off=0
1780866143	13.6 V	28 F	0 On=255 Off=0
1780865245	13.7 V	28 F	0 On=255 Off=0
1780863447	13.6 V	28 F	0 On=255 Off=0
1780861645	13.5 V	28 F	0 On=255 Off=0
1780858045	13.5 V	27 F	0 On=255 Off=0
1780856245	14 V	28 F	0 On=255 Off=0
1780855345	13.5 V	27 F	0 On=255 Off=0
1780853546	13.5 V	28 F	0 On=255 Off=0

*Used Equation Coefficients:

Battery: 0, 0.1, 0

PC Board Temp: 0, 1, 0

-: 0, 1, 0

-: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)