K1EQX-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K1EQX-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1761535086	14.1 Volt	1160 Pkt	400 Pkt	67 Pcnt
1761533285	14.1 Volt	1140 Pkt	400 Pkt	69 Pcnt
1761531483	14.1 Volt	1070 Pkt	380 Pkt	67 Pcnt
1761529681	14.1 Volt	1060 Pkt	390 Pkt	66 Pcnt
1761527879	14.1 Volt	1100 Pkt	410 Pkt	67 Pcnt
1761526079	14.1 Volt	1060 Pkt	380 Pkt	65 Pcnt
1761524276	14.1 Volt	1070 Pkt	370 Pkt	64 Pcnt
1761522474	14.1 Volt	1130 Pkt	370 Pkt	64 Pcnt
1761520672	14.1 Volt	1190 Pkt	360 Pkt	66 Pcnt
1761518871	14.1 Volt	1190 Pkt	360 Pkt	66 Pcnt
1761517070	14.1 Volt	1180 Pkt	380 Pkt	66 Pcnt
1761515269	14.1 Volt	1180 Pkt	390 Pkt	65 Pcnt
1761513465	14.1 Volt	1200 Pkt	370 Pkt	65 Pcnt
1761511664	14.1 Volt	1240 Pkt	390 Pkt	65 Pcnt
1761509862	14.1 Volt	1240 Pkt	400 Pkt	65 Pcnt
1761508060	14.1 Volt	1250 Pkt	410 Pkt	65 Pcnt
1761506259	14.1 Volt	1240 Pkt	420 Pkt	65 Pcnt
1761504463	14.1 Volt	1220 Pkt	400 Pkt	65 Pcnt
1761502655	14.1 Volt	1240 Pkt	390 Pkt	64 Pcnt
1761500853	14.1 Volt	1220 Pkt	390 Pkt	64 Pcnt
1761499052	14.1 Volt	1160 Pkt	400 Pkt	66 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)