IT9LTA-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IT9LTA-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1784689479	33.1 C deg	49.3 %	0 C deg
1784687664	33 C deg	51.4 %	0 C deg
1784685849	33.2 C deg	51.4 %	0 C deg
1784684037	33.2 C deg	52.2 %	0 C deg
1784682222	33.1 C deg	52.7 %	0 C deg
1784680405	33.4 C deg	53.4 %	0 C deg
1784678590	33.4 C deg	55.5 %	0 C deg
1784676775	33.3 C deg	55.4 %	0 C deg
1784674964	33.6 C deg	55.4 %	0 C deg
1784673149	33.9 C deg	51.4 %	0 C deg
1784671330	34 C deg	49.6 %	0 C deg
1784669515	34 C deg	49 %	0 C deg
1784667700	33.9 C deg	53.8 %	0 C deg
1784665885	33.8 C deg	58.9 %	0 C deg
1784664066	33.5 C deg	59.7 %	0 C deg
1784662251	33.1 C deg	61.7 %	0 C deg
1784660436	33.3 C deg	61.2 %	0 C deg
1784658621	32.8 C deg	61 %	0 C deg
1784656802	33.3 C deg	57.7 %	0 C deg
1784654987	33.3 C deg	54.3 %	0 C deg
1784653172	33.7 C deg	53.8 %	0 C deg
1784651357	33.5 C deg	56.3 %	0 C deg
1784649541	33.6 C deg	53.7 %	0 C deg
1784647726	33.6 C deg	51.6 %	0 C deg
1784645911	33.6 C deg	48 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)