KC9NPJ-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC9NPJ-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vlt*	Rx1h*	Eff1h*
1776681662	13.65 Volt	160 Pkt	37 Pcnt
1776678062	13.65 Volt	160 Pkt	42 Pcnt
1776674462	13.65 Volt	80 Pkt	29 Pcnt
1776670862	13.65 Volt	70 Pkt	36 Pcnt
1776667262	13.65 Volt	80 Pkt	47 Pcnt
1776663663	13.65 Volt	80 Pkt	42 Pcnt
1776660063	13.65 Volt	80 Pkt	38 Pcnt
1776656463	13.65 Volt	90 Pkt	45 Pcnt
1776652863	13.65 Volt	90 Pkt	52 Pcnt
1776649263	13.65 Volt	80 Pkt	52 Pcnt
1776645663	13.65 Volt	70 Pkt	43 Pcnt
1776642064	13.65 Volt	40 Pkt	35 Pcnt
1776638464	13.65 Volt	20 Pkt	35 Pcnt
1776634864	13.65 Volt	30 Pkt	35 Pcnt
1776631264	13.73 Volt	30 Pkt	35 Pcnt
1776627664	13.65 Volt	20 Pkt	29 Pcnt
1776624065	13.65 Volt	20 Pkt	24 Pcnt
1776620465	13.65 Volt	20 Pkt	29 Pcnt
1776616865	13.65 Volt	30 Pkt	49 Pcnt
1776613265	13.73 Volt	30 Pkt	42 Pcnt
1776609665	13.73 Volt	70 Pkt	26 Pcnt
1776606066	13.73 Volt	940 Pkt	65 Pcnt
1776602466	13.8 Volt	720 Pkt	61 Pcnt
1776598866	13.8 Volt	620 Pkt	62 Pcnt
1776595266	13.8 Volt	520 Pkt	56 Pcnt

*Used Equation Coefficients:

Vlt: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)