DG0OPK-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0OPK-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1789946788	20 C deg	57.8 %	7.2 C deg
1789946739	20 C deg	57.8 %	7.2 C deg
1789943088	19.9 C deg	56.7 %	7.1 C deg
1789939419	19.8 C deg	56 %	7.9 C deg
1789937592	19.7 C deg	55.1 %	9 C deg
1789935832	17.2 C deg	57.7 %	10.5 C deg
1789935761	17.2 C deg	57.7 %	10.5 C deg
1789933986	18.3 C deg	57.5 %	11.1 C deg
1789933929	18.3 C deg	57.5 %	11.1 C deg
1789932253	20.6 C deg	57.5 %	11.4 C deg
1789932106	20.6 C deg	57.5 %	11.4 C deg
1789926730	20.1 C deg	58 %	13.8 C deg
1789926607	20.1 C deg	58 %	13.8 C deg
1789925171	20.3 C deg	58.4 %	14 C deg
1789924778	20.3 C deg	58.4 %	14 C deg
1789923144	20.3 C deg	60.1 %	18.5 C deg
1789922947	20.3 C deg	60.1 %	18.5 C deg
1789919515	20.4 C deg	61 %	14.9 C deg
1789919287	20.4 C deg	61 %	14.9 C deg
1789915659	20.4 C deg	65.8 %	15 C deg
1789913799	20.4 C deg	64.9 %	14.8 C deg
1789911970	21.2 C deg	57.6 %	14.9 C deg
1789910151	21.3 C deg	55.6 %	14.8 C deg
1789908308	21.1 C deg	55.4 %	14.8 C deg
1789904649	20.9 C deg	55.5 %	15.1 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)