OE6POD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE6POD. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1776690260	14.8 deg C	40.5 %	1010.8 hPa
1776689360	14.2 deg C	41.3 %	1011.2 hPa
1776688460	15.5 deg C	40.2 %	1010.9 hPa
1776688128	13.3 deg C	43.3 %	1011.6 hPa
1776687228	19.6 deg C	34.1 %	1009.7 hPa
1776686328	16.8 deg C	38.9 %	1010.8 hPa
1776685428	14.5 deg C	41.9 %	1011.6 hPa
1776684528	15.1 deg C	43.3 %	1011.5 hPa
1776683628	13.5 deg C	46.6 %	1012.3 hPa
1776682728	15.1 deg C	44.4 %	1011.9 hPa
1776681828	16.9 deg C	40.5 %	1011.7 hPa
1776680927	16 deg C	40.1 %	1012.1 hPa
1776680027	15.7 deg C	42.6 %	1012.4 hPa
1776679127	17.2 deg C	39.3 %	1012.1 hPa
1776678227	16.4 deg C	40.4 %	1012.6 hPa
1776677327	15.3 deg C	43.7 %	1013.2 hPa
1776676427	13.4 deg C	48.5 %	1014 hPa
1776676097	12.7 deg C	49.3 %	1014.3 hPa
1776675196	14.2 deg C	45.2 %	1013.9 hPa
1776674296	13.7 deg C	46.3 %	1014.2 hPa
1776673396	10.9 deg C	54.4 %	1015.2 hPa
1776672496	13.5 deg C	49 %	1014.5 hPa
1776671596	11.3 deg C	56.8 %	1015.2 hPa
1776670696	13 deg C	53.5 %	1014.7 hPa
1776669796	11 deg C	56.6 %	1015.2 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)