VA3XLT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA3XLT. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Rx10m*
1761616829	12.6 Volt	100 Pcnt	0 Pkt
1761616529	12.6 Volt	100 Pcnt	0 Pkt
1761616229	12.6 Volt	100 Pcnt	0 Pkt
1761615929	12.6 Volt	100 Pcnt	0 Pkt
1761615629	12.6 Volt	100 Pcnt	1 Pkt
1761615329	12.6 Volt	100 Pcnt	1 Pkt
1761615029	12.6 Volt	100 Pcnt	0 Pkt
1761614729	12.6 Volt	100 Pcnt	2 Pkt
1761614429	12.6 Volt	100 Pcnt	2 Pkt
1761614129	12.6 Volt	100 Pcnt	0 Pkt
1761613829	12.6 Volt	100 Pcnt	1 Pkt
1761613529	12.6 Volt	100 Pcnt	1 Pkt
1761613229	12.6 Volt	100 Pcnt	0 Pkt
1761612929	12.6 Volt	100 Pcnt	0 Pkt
1761612629	12.6 Volt	100 Pcnt	0 Pkt
1761612329	12.6 Volt	100 Pcnt	0 Pkt
1761612029	12.6 Volt	100 Pcnt	1 Pkt
1761611729	12.6 Volt	100 Pcnt	1 Pkt
1761611429	12.6 Volt	100 Pcnt	0 Pkt
1761611129	12.6 Volt	100 Pcnt	2 Pkt
1761610829	12.6 Volt	100 Pcnt	2 Pkt
1761610529	12.6 Volt	100 Pcnt	0 Pkt
1761610229	12.6 Volt	100 Pcnt	1 Pkt
1761609929	12.6 Volt	100 Pcnt	1 Pkt
1761609629	12.6 Volt	100 Pcnt	0 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Rx10m: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)