HUGOCO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HUGOCO. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1776952652	14.14 Volt	600 Pkt	140 Pkt	98 Pcnt
1776951752	14.14 Volt	580 Pkt	130 Pkt	98 Pcnt
1776950852	14.14 Volt	590 Pkt	130 Pkt	98 Pcnt
1776949952	14.14 Volt	590 Pkt	130 Pkt	98 Pcnt
1776949052	14.14 Volt	580 Pkt	120 Pkt	98 Pcnt
1776948152	14.14 Volt	570 Pkt	110 Pkt	98 Pcnt
1776947252	14.14 Volt	510 Pkt	110 Pkt	98 Pcnt
1776946352	14.14 Volt	480 Pkt	100 Pkt	99 Pcnt
1776945452	14.14 Volt	460 Pkt	100 Pkt	99 Pcnt
1776944552	14.14 Volt	460 Pkt	100 Pkt	99 Pcnt
1776943652	14.14 Volt	460 Pkt	100 Pkt	99 Pcnt
1776942752	14.14 Volt	450 Pkt	100 Pkt	99 Pcnt
1776941852	14.14 Volt	460 Pkt	100 Pkt	99 Pcnt
1776940952	14.14 Volt	470 Pkt	100 Pkt	98 Pcnt
1776940052	14.14 Volt	470 Pkt	100 Pkt	98 Pcnt
1776939152	14.14 Volt	470 Pkt	110 Pkt	98 Pcnt
1776938252	14.14 Volt	460 Pkt	100 Pkt	98 Pcnt
1776937352	14.14 Volt	450 Pkt	100 Pkt	99 Pcnt
1776936452	14.14 Volt	440 Pkt	100 Pkt	99 Pcnt
1776935552	14.14 Volt	460 Pkt	100 Pkt	99 Pcnt
1776934652	14.14 Volt	450 Pkt	90 Pkt	99 Pcnt
1776933752	14.14 Volt	440 Pkt	90 Pkt	99 Pcnt
1776932852	14.14 Volt	450 Pkt	90 Pkt	99 Pcnt
1776931953	14.14 Volt	410 Pkt	90 Pkt	92 Pcnt
1776931053	14.14 Volt	360 Pkt	90 Pkt	85 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)