DB0ESS-L4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0ESS-L4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1757603526	23.6 deg C	28.9 %	1131 hPa
1757602626	23.6 deg C	29 %	1131 hPa
1757601726	23.6 deg C	29 %	1130.8 hPa
1757600826	23.5 deg C	29 %	1130.6 hPa
1757599926	23.5 deg C	29 %	1130.6 hPa
1757599026	23.5 deg C	28.8 %	1130.4 hPa
1757598126	23.5 deg C	28.8 %	1130.3 hPa
1757597226	23.4 deg C	29 %	1130.1 hPa
1757596326	23.4 deg C	28.7 %	1129.9 hPa
1757595426	23.4 deg C	28.3 %	1130 hPa
1757594525	23.5 deg C	28.9 %	1129.9 hPa
1757593625	23.5 deg C	28.6 %	1129.8 hPa
1757592725	23.5 deg C	29 %	1129.7 hPa
1757591825	23.5 deg C	29.3 %	1129.6 hPa
1757590925	23.5 deg C	29.4 %	1129.3 hPa
1757590040	23.5 deg C	29.3 %	1129 hPa
1757589125	23.5 deg C	29 %	1129 hPa
1757588225	23.4 deg C	29.2 %	1128.9 hPa
1757587325	23.4 deg C	29.4 %	1129 hPa
1757586425	23.4 deg C	29.6 %	1128.9 hPa
1757586101	23.4 deg C	29.7 %	1128.9 hPa
1757585216	23.3 deg C	29.7 %	1129.1 hPa
1757584301	23.3 deg C	29.8 %	1129.2 hPa
1757583400	23.3 deg C	29.9 %	1129.3 hPa
1757582500	23.2 deg C	30 %	1129.3 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)