VK6RTH-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK6RTH-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Supply*	ADC0*
1787573868	21.12 DegC	12.47 Volt	249 None
1787572066	23.08 DegC	12.47 Volt	249 None
1787570262	25.04 DegC	12.47 Volt	249 None
1787568449	23.08 DegC	12.55 Volt	249 None
1787566638	23.08 DegC	12.55 Volt	249 None
1787564833	25.04 DegC	12.55 Volt	249 None
1787563013	23.08 DegC	12.78 Volt	250 None
1787561211	23.08 DegC	12.78 Volt	250 None
1787559402	25.04 DegC	12.86 Volt	250 None
1787557598	25.04 DegC	13.41 Volt	250 None
1787555789	27 DegC	14.43 Volt	251 None
1787553987	25.04 DegC	13.65 Volt	250 None
1787552268	23.08 DegC	14.43 Volt	251 None
1787550371	25.04 DegC	13.73 Volt	251 None
1787548564	25.04 DegC	14.43 Volt	251 None
1787546760	25.04 DegC	14.35 Volt	251 None
1787544955	25.04 DegC	14.35 Volt	251 None
1787543149	25.04 DegC	13.1 Volt	250 None
1787541339	23.08 DegC	14.04 Volt	252 None
1787539531	23.08 DegC	13.25 Volt	250 None
1787537719	21.12 DegC	13.8 Volt	250 None
1787535903	21.12 DegC	13.57 Volt	250 None
1787534093	21.12 DegC	13.41 Volt	250 None
1787532280	19.16 DegC	13.25 Volt	251 None
1787530466	19.16 DegC	13.02 Volt	250 None

*Used Equation Coefficients:

Temp: 0, 1.9608, -273

Supply: 0, 0.07843, 0

ADC0: 0, 1, 0

Cnt: 0, 1, 0

HDOP: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)