LA3SHA-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LA3SHA-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1773046786	14.25 Volt	0 Pcnt	1.5 C
1773044986	14.18 Volt	0 Pcnt	1 C
1773043186	14.18 Volt	0 Pcnt	0 C
1773041386	14.18 Volt	0 Pcnt	0 C
1773039586	12.53 Volt	0 Pcnt	0 C
1773037787	12.53 Volt	0 Pcnt	-1 C
1773035987	12.53 Volt	0 Pcnt	-1 C
1773034187	12.53 Volt	0 Pcnt	0 C
1773032387	12.53 Volt	0 Pcnt	-0.5 C
1773030587	12.53 Volt	0 Pcnt	0 C
1773028787	12.53 Volt	0 Pcnt	0 C
1773026987	12.53 Volt	0 Pcnt	0 C
1773025187	12.53 Volt	0 Pcnt	0 C
1773023387	12.53 Volt	0 Pcnt	-0.5 C
1773021587	12.53 Volt	0 Pcnt	0 C
1773019787	12.53 Volt	0 Pcnt	0 C
1773017987	12.53 Volt	0 Pcnt	1 C
1773016188	12.53 Volt	100 Pcnt	0 C
1773014388	12.53 Volt	0 Pcnt	0.5 C
1773012588	12.53 Volt	0 Pcnt	0 C
1773010788	12.6 Volt	0 Pcnt	0 C
1773008988	12.6 Volt	0 Pcnt	0.5 C
1773007188	12.6 Volt	0 Pcnt	0.5 C
1773005388	12.6 Volt	0 Pcnt	0.5 C
1773003588	12.6 Volt	0 Pcnt	0.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)