This is the latest recevied telemetry packets stored in our database for station/object SQ9CH-0. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Vin*
Rx1h*
Dg1h*
Eff1h*
A5*
1788579938
12.38 Volt
140 Pkt
40 Pkt
79 Pcnt
0 None
1788572732
12.38 Volt
160 Pkt
70 Pkt
71 Pcnt
0 None
1788558318
12.38 Volt
160 Pkt
70 Pkt
86 Pcnt
0 None
1788551110
12.38 Volt
130 Pkt
60 Pkt
81 Pcnt
0 None
1788515076
12.38 Volt
120 Pkt
40 Pkt
79 Pcnt
0 None
1788486248
12.38 Volt
140 Pkt
60 Pkt
82 Pcnt
0 None
1788464628
12.38 Volt
360 Pkt
110 Pkt
90 Pcnt
0 None
1788277250
12.38 Volt
280 Pkt
90 Pkt
91 Pcnt
0 None
1788234009
12.38 Volt
210 Pkt
60 Pkt
85 Pcnt
0 None
1788226802
12.38 Volt
230 Pkt
70 Pkt
85 Pcnt
0 None
1788205181
12.38 Volt
360 Pkt
90 Pkt
70 Pcnt
0 None
1788197974
12.38 Volt
330 Pkt
140 Pkt
87 Pcnt
0 None
1788176353
12.38 Volt
220 Pkt
90 Pkt
84 Pcnt
0 None
1787852046
12.38 Volt
250 Pkt
120 Pkt
87 Pcnt
0 None
1787837631
12.38 Volt
190 Pkt
100 Pkt
89 Pcnt
0 None
1787830424
12.38 Volt
120 Pkt
50 Pkt
82 Pcnt
0 None
1787823217
12.38 Volt
110 Pkt
40 Pkt
78 Pcnt
0 None
*Used Equation Coefficients:
Vin: 0, 0.075, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
A5: 0, 0, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)