MB7UHG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UHG. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	CabT*
1785326170	13.8 Volt	100 Pcnt	179 c
1785325270	13.8 Volt	100 Pcnt	179 c
1785324370	13.8 Volt	100 Pcnt	179 c
1785323470	13.8 Volt	100 Pcnt	179 c
1785322570	13.8 Volt	100 Pcnt	179 c
1785321670	13.8 Volt	100 Pcnt	178 c
1785320770	13.8 Volt	100 Pcnt	178 c
1785319870	13.8 Volt	0 Pcnt	177 c
1785318970	13.8 Volt	0 Pcnt	177 c
1785318070	13.8 Volt	0 Pcnt	176 c
1785317170	13.8 Volt	0 Pcnt	176 c
1785316270	13.8 Volt	100 Pcnt	176 c
1785315407	13.8 Volt	100 Pcnt	175 c
1785314470	13.8 Volt	100 Pcnt	175 c
1785313570	13.8 Volt	100 Pcnt	174 c
1785312670	13.8 Volt	100 Pcnt	174 c
1785311770	13.8 Volt	100 Pcnt	174 c
1785310870	13.8 Volt	100 Pcnt	174 c
1785309970	13.8 Volt	100 Pcnt	174 c
1785309070	13.8 Volt	100 Pcnt	174 c
1785308170	13.8 Volt	100 Pcnt	174 c
1785307270	13.8 Volt	100 Pcnt	173 c
1785306370	13.8 Volt	100 Pcnt	173 c
1785305470	13.8 Volt	100 Pcnt	173 c
1785304570	13.8 Volt	100 Pcnt	173 c

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

CabT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)