UBUTTE Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UBUTTE. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Solar*	Rx1h*
1788683288	12.5 Volt	0.5 Volts	550 Pkt
1788682989	12.5 Volt	0.5 Volts	550 Pkt
1788682988	12.5 Volt	0.5 Volts	550 Pkt
1788682688	12.5 Volt	0.5 Volts	560 Pkt
1788682389	12.5 Volt	0.5 Volts	560 Pkt
1788682388	12.5 Volt	0.5 Volts	560 Pkt
1788682088	12.5 Volt	0.5 Volts	560 Pkt
1788681789	12.5 Volt	0.5 Volts	560 Pkt
1788681788	12.5 Volt	0.5 Volts	560 Pkt
1788681488	12.5 Volt	0.5 Volts	560 Pkt
1788681189	12.5 Volt	0.5 Volts	540 Pkt
1788681188	12.5 Volt	0.5 Volts	540 Pkt
1788680888	12.5 Volt	0.5 Volts	550 Pkt
1788680589	12.5 Volt	0.5 Volts	540 Pkt
1788680588	12.5 Volt	0.5 Volts	540 Pkt
1788680289	12.5 Volt	0.5 Volts	540 Pkt
1788679989	12.5 Volt	0.5 Volts	540 Pkt
1788679988	12.5 Volt	0.5 Volts	540 Pkt
1788679689	12.5 Volt	0.5 Volts	540 Pkt
1788679389	12.5 Volt	0.5 Volts	540 Pkt
1788679389	12.5 Volt	0.5 Volts	540 Pkt
1788679089	12.5 Volt	0.5 Volts	520 Pkt
1788678789	12.5 Volt	0.5 Volts	540 Pkt
1788678788	12.5 Volt	0.5 Volts	540 Pkt
1788678489	12.5 Volt	0.5 Volts	540 Pkt

*Used Equation Coefficients:

Vin: 0, 0.1, 0

Solar: 0, 0.1, 0

Dig1h: 0, 10, 0

Rx1h: 0, 10, 0

Cur: 0, 0.1953, -24.8031

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)