YO8CLN-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO8CLN-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	T*	Eff1h*
1784668537	1010 V	1510 C	25 Pcnt
1784665530	1120 V	1510 C	23 Pcnt
1784662572	1210 V	1530 C	19 Pcnt
1784659525	1230 V	1540 C	24 Pcnt
1784656516	1230 V	1570 C	18 Pcnt
1784653554	1230 V	1580 C	24 Pcnt
1784650520	1250 V	1600 C	18 Pcnt
1784647509	1260 V	1600 C	18 Pcnt
1784644526	1310 V	1600 C	20 Pcnt
1784641504	1300 V	1590 C	20 Pcnt
1784638544	1350 V	1580 C	25 Pcnt
1784635496	1360 V	1570 C	23 Pcnt
1784632493	1370 V	1570 C	21 Pcnt
1784629494	1350 V	1560 C	24 Pcnt
1784626489	1360 V	1560 C	19 Pcnt
1784623497	1360 V	1550 C	17 Pcnt
1784620484	1360 V	1530 C	17 Pcnt
1784617482	1380 V	1510 C	20 Pcnt
1784614478	1360 V	1490 C	27 Pcnt
1784611479	1400 V	1480 C	32 Pcnt
1784608479	1400 V	1460 C	22 Pcnt
1784605467	1270 V	1440 C	0 Pcnt
1784581037	1080 V	1500 C	36 Pcnt
1784578039	1130 V	1520 C	35 Pcnt
1784575080	1210 V	1540 C	20 Pcnt

*Used Equation Coefficients:

Vin: 0, 10, 0

T: 0, 10, 0

Eff1h: 0, 1, 0

RX: 0, 0, 0

TX: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)