OM3KFF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OM3KFF-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CpuTemp*	Load1*	Uptime*	RX*	TX*
1789945910	58.5 degC	0.02	10.2 d	14 pkt	0 pkt
1789945314	57.5 degC	0.03	10.2 d	20 pkt	0 pkt
1789944714	57.5 degC	0.12	10.2 d	16 pkt	0 pkt
1789944114	58.5 degC	0.34	10.2 d	11 pkt	0 pkt
1789943510	58.5 degC	0.76	10.2 d	6 pkt	1 pkt
1789942910	58.5 degC	0.15	10.1 d	5 pkt	1 pkt
1789942310	58.5 degC	0.05	10.1 d	7 pkt	0 pkt
1789941714	57.5 degC	0.28	10.1 d	7 pkt	0 pkt
1789941114	57.5 degC	0.18	10.1 d	8 pkt	0 pkt
1789940513	57.5 degC	0.75	10.1 d	4 pkt	0 pkt
1789939910	57.5 degC	0.52	10.1 d	8 pkt	1 pkt
1789939309	57.5 degC	0.44	10.1 d	5 pkt	1 pkt
1789938710	57.5 degC	0.02	10.1 d	3 pkt	0 pkt
1789938114	57.5 degC	0.12	10.1 d	2 pkt	0 pkt
1789937513	57.5 degC	0.31	10.1 d	2 pkt	0 pkt
1789936913	59 degC	0.79	10.1 d	0 pkt	0 pkt
1789936309	58.5 degC	0.33	10.1 d	2 pkt	1 pkt
1789935710	57.5 degC	0.02	10.1 d	3 pkt	1 pkt
1789935110	58.5 degC	0.04	10.1 d	6 pkt	0 pkt
1789934513	58.5 degC	0.23	10 d	2 pkt	0 pkt
1789933914	57.5 degC	0.35	10 d	2 pkt	0 pkt
1789933314	57.5 degC	0.36	10 d	1 pkt	0 pkt
1789932710	57.5 degC	0.06	10 d	3 pkt	1 pkt
1789932110	58.5 degC	0.51	10 d	2 pkt	1 pkt
1789931510	57.5 degC	0	10 d	2 pkt	0 pkt

*Used Equation Coefficients:

CpuTemp: 0, 0.5, 0

Load1: 0, 0.01, 0

Uptime: 0, 0.1, 0

RX: 0, 1, 0

TX: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)