SQ3KT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ3KT-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1787569566	64 Count	697 Count	4.2 VDC
1787568665	63 Count	669 Count	4.21 VDC
1787567764	62 Count	643 Count	4.24 VDC
1787567755	62 Count	669 Count	4.22 VDC
1787566854	61 Count	643 Count	4.22 VDC
1787565953	60 Count	623 Count	4.19 VDC
1787565052	59 Count	608 Count	4.21 VDC
1787564152	58 Count	585 Count	4.29 VDC
1787563669	57 Count	585 Count	4.23 VDC
1787562768	56 Count	576 Count	4.23 VDC
1787561867	55 Count	566 Count	4.21 VDC
1787560967	54 Count	555 Count	4.19 VDC
1787560066	53 Count	544 Count	4.29 VDC
1787559165	52 Count	534 Count	4.27 VDC
1787558264	51 Count	523 Count	4.18 VDC
1787557364	50 Count	512 Count	4.29 VDC
1787556463	49 Count	502 Count	4.28 VDC
1787555562	48 Count	491 Count	4.25 VDC
1787554661	47 Count	481 Count	4.2 VDC
1787553760	46 Count	470 Count	4.24 VDC
1787552860	45 Count	461 Count	4.21 VDC
1787551959	44 Count	450 Count	4.18 VDC
1787551058	43 Count	440 Count	4.21 VDC
1787550157	42 Count	429 Count	4.18 VDC
1787549257	41 Count	418 Count	4.21 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)