OK4AB-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK4AB-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1787429867	23.7 C	55.46 %	1021.88 hPa
1787428963	23.7 C	55.46 %	1023.25 hPa
1787427155	23.8 C	55.27 %	1021.13 hPa
1787424444	23.9 C	55.11 %	1022.25 hPa
1787422637	24 C	54.77 %	1021.25 hPa
1787421733	24.1 C	54.55 %	1021 hPa
1787420829	24.2 C	54.32 %	1020.75 hPa
1787419926	24.3 C	54.25 %	1020.25 hPa
1787419022	24.4 C	54.15 %	1020.63 hPa
1787418118	24.5 C	54.02 %	1020.5 hPa
1787417214	24.5 C	54.08 %	1020 hPa
1787416311	24.6 C	53.88 %	1019.75 hPa
1787415407	24.7 C	53.83 %	1020.88 hPa
1787414503	24.7 C	54.34 %	1019.75 hPa
1787413599	24.5 C	54.52 %	1019.75 hPa
1787412696	24.5 C	54.97 %	1019.38 hPa
1787411792	24.4 C	55.27 %	1020.38 hPa
1787410888	24.2 C	55.58 %	1020.5 hPa
1787409984	24 C	55.62 %	1019.63 hPa
1787409080	23.9 C	55.8 %	1019.25 hPa
1787408159	23.4 C	56.34 %	977.25 hPa
1787395290	19 C	67.28 %	1016.13 hPa
1787394385	18.7 C	69.72 %	1015.63 hPa
1787393483	18.4 C	68.81 %	1016.38 hPa
1787392578	18.1 C	70 %	1017 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)