BM3DQG-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3DQG-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*
1761506471	55 C	11 p	82 p	2086 p
1761505270	55 C	14 p	82 p	2061 p
1761502870	55 C	13 p	76 p	2004 p
1761501670	55 C	13 p	84 p	1979 p
1761500470	55 C	14 p	85 p	1956 p
1761498070	55 C	14 p	97 p	1895 p
1761496870	55 C	16 p	117 p	1871 p
1761495670	55 C	18 p	111 p	1835 p
1761494470	55 C	20 p	99 p	1799 p
1761493270	55 C	15 p	79 p	1754 p
1761492070	55 C	12 p	77 p	1724 p
1761489669	55 C	13 p	86 p	1675 p
1761488470	55 C	13 p	107 p	1647 p
1761486070	55 C	25 p	112 p	1589 p
1761484870	55 C	23 p	93 p	1540 p
1761483670	55 C	15 p	102 p	1502 p
1761482469	55 C	5 p	103 p	1477 p
1761481270	55 C	20 p	98 p	1447 p
1761480070	55 C	17 p	104 p	1400 p
1761477669	55 C	28 p	150 p	1349 p
1761476470	55 C	28 p	172 p	1296 p
1761475270	55 C	20 p	164 p	1245 p
1761472870	55 C	22 p	117 p	1124 p
1761471670	55 C	12 p	103 p	1081 p
1761470470	55 C	21 p	112 p	1052 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)