F1ZDB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F1ZDB-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Batt*	RX*	Relay*	Drop*
1788568988	4.3 VDC	46 pkt	16 pkt	30 pkt
1788568088	4.29 VDC	37 pkt	15 pkt	22 pkt
1788567188	4.3 VDC	44 pkt	16 pkt	28 pkt
1788566288	4.29 VDC	58 pkt	21 pkt	37 pkt
1788565388	4.29 VDC	44 pkt	19 pkt	25 pkt
1788564487	4.31 VDC	37 pkt	16 pkt	21 pkt
1788563587	4.29 VDC	35 pkt	13 pkt	22 pkt
1788562687	4.3 VDC	37 pkt	16 pkt	21 pkt
1788561787	4.3 VDC	46 pkt	17 pkt	29 pkt
1788560886	4.3 VDC	45 pkt	19 pkt	26 pkt
1788559986	4.31 VDC	37 pkt	16 pkt	21 pkt
1788559086	4.3 VDC	33 pkt	14 pkt	19 pkt
1788558186	4.31 VDC	38 pkt	15 pkt	23 pkt
1788557286	4.29 VDC	34 pkt	14 pkt	20 pkt
1788556385	4.3 VDC	40 pkt	18 pkt	22 pkt
1788555485	4.31 VDC	31 pkt	15 pkt	16 pkt
1788554584	4.3 VDC	0 pkt	0 pkt	0 pkt
1788553691	4.3 VDC	46 pkt	15 pkt	31 pkt
1788552791	4.29 VDC	39 pkt	11 pkt	28 pkt
1788551891	4.3 VDC	46 pkt	15 pkt	31 pkt
1788550991	4.29 VDC	47 pkt	13 pkt	34 pkt
1788550090	4.3 VDC	46 pkt	17 pkt	29 pkt
1788549190	4.29 VDC	47 pkt	17 pkt	30 pkt
1788548290	4.31 VDC	41 pkt	16 pkt	25 pkt
1788547390	4.31 VDC	33 pkt	16 pkt	17 pkt

*Used Equation Coefficients:

V_Batt: 0, 0.01, 0

RX: 0, 1, 0

Relay: 0, 1, 0

Drop: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)