This is the latest recevied telemetry packets stored in our database for station/object CR7BQP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Battery*
Charging/AC*
GPS+Sat*
Current*
A5*
1763343364
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763342464
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763341564
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763339763
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763338863
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763337963
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763337063
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763336162
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763334362
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763333462
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763332561
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763328295
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763327814
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
1763326913
100 Percent
48 Charge/On/Off
2 Sats/On/Off
0 mA
0 N/A
*Used Equation Coefficients:
Battery: 0, 1, 0
Charging/AC: 0, 1, 0
GPS+Sat: 0, 1, 0
Current: 0, 10, -1280
A5: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)