MB7UHT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UHT. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp_Int*	Temp_Ext*
1753845476	15.6 deg.C	15.6 deg.C
1753844275	15.6 deg.C	15.6 deg.C
1753841875	14.8 deg.C	14.9 deg.C
1753840676	14.7 deg.C	14.7 deg.C
1753839475	14.4 deg.C	14.6 deg.C
1753835876	13.9 deg.C	13.9 deg.C
1753834675	14.1 deg.C	14 deg.C
1753833476	14.3 deg.C	14.3 deg.C
1753832276	14.7 deg.C	14.4 deg.C
1753831076	15.6 deg.C	14.8 deg.C
1753829876	15.3 deg.C	15.1 deg.C
1753828676	15.8 deg.C	15.6 deg.C
1753827476	16.3 deg.C	16.6 deg.C
1753826276	17 deg.C	16.4 deg.C
1753825076	17.5 deg.C	17.3 deg.C
1753823876	17.8 deg.C	17.6 deg.C
1753821476	18.6 deg.C	18.3 deg.C
1753820276	19.6 deg.C	18.8 deg.C
1753817876	19.8 deg.C	19.6 deg.C
1753816675	20.6 deg.C	19.9 deg.C
1753815476	20.3 deg.C	20.3 deg.C
1753814276	20.4 deg.C	20.4 deg.C
1753813076	20.6 deg.C	20.5 deg.C
1753811876	21.6 deg.C	20.8 deg.C
1753810681	21.7 deg.C	21.4 deg.C

*Used Equation Coefficients:

Temp_Int: 0, 0.1, 0

Temp_Ext: 0, 0.1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)