SR9SMR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9SMR. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Vbatt*	Tempre*
1784679898	31 Pkt	2 Pkt	11.86 V	0 DegC
1784679255	29 Pkt	2 Pkt	11.86 V	0 DegC
1784678621	24 Pkt	2 Pkt	11.86 V	0 DegC
1784677988	33 Pkt	2 Pkt	11.88 V	0 DegC
1784677344	26 Pkt	8 Pkt	11.84 V	0 DegC
1784676704	26 Pkt	2 Pkt	11.84 V	0 DegC
1784676071	26 Pkt	2 Pkt	11.88 V	0 DegC
1784675438	27 Pkt	2 Pkt	11.82 V	0 DegC
1784674794	31 Pkt	2 Pkt	11.88 V	0 DegC
1784674794	31 Pkt	2 Pkt	11.86 V	0 DegC
1784674161	26 Pkt	3 Pkt	11.86 V	0 DegC
1784673526	35 Pkt	2 Pkt	11.86 V	0 DegC
1784672882	30 Pkt	2 Pkt	11.86 V	0 DegC
1784672249	27 Pkt	2 Pkt	11.84 V	0 DegC
1784671605	30 Pkt	3 Pkt	11.82 V	0 DegC
1784670970	35 Pkt	2 Pkt	11.88 V	0 DegC
1784670326	30 Pkt	3 Pkt	11.86 V	0 DegC
1784669692	34 Pkt	2 Pkt	11.88 V	0 DegC
1784669692	34 Pkt	2 Pkt	11.86 V	0 DegC
1784669048	26 Pkt	2 Pkt	11.86 V	0 DegC
1784668415	38 Pkt	2 Pkt	11.84 V	0 DegC
1784668415	38 Pkt	2 Pkt	10 V	-50 DegC
1784667387	27 Pkt	3 Pkt	11.88 V	0 DegC
1784666701	34 Pkt	3 Pkt	11.88 V	0 DegC
1784665988	27 Pkt	2 Pkt	11.86 V	0 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)