SP6OOL-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6OOL-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1761520906	85 Count	616 Count	4.33 VDC
1761520005	84 Count	611 Count	4.6 VDC
1761519111	83 Count	604 Count	4.72 VDC
1761518204	82 Count	599 Count	4.42 VDC
1761517303	81 Count	593 Count	4.49 VDC
1761516403	80 Count	588 Count	4.43 VDC
1761515502	79 Count	582 Count	4.76 VDC
1761514602	78 Count	577 Count	4.7 VDC
1761513701	77 Count	573 Count	4.26 VDC
1761512800	76 Count	568 Count	4.4 VDC
1761511900	75 Count	562 Count	4.48 VDC
1761510999	74 Count	557 Count	4.17 VDC
1761510099	73 Count	551 Count	4.81 VDC
1761509198	72 Count	547 Count	4.47 VDC
1761508297	71 Count	540 Count	4.13 VDC
1761507397	70 Count	536 Count	4.56 VDC
1761506496	69 Count	529 Count	4.28 VDC
1761505596	68 Count	523 Count	4.18 VDC
1761504709	67 Count	515 Count	4.42 VDC
1761503808	66 Count	505 Count	4.15 VDC
1761502908	65 Count	497 Count	4.38 VDC
1761502007	64 Count	487 Count	4.55 VDC
1761500206	62 Count	459 Count	4.28 VDC
1761498405	60 Count	449 Count	4.11 VDC
1761497504	59 Count	443 Count	4.66 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)