OK1TOR-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1TOR-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU_temp*	Load*	Fmem*	Nodes[I]*	Dests[F]*
1773201610	52.6 °C	0.94	47 MB	321	48
1773197288	52 °C	0.44	46 MB	334	48
1773195847	52 °C	0.6	46 MB	335	48
1773192244	53.6 °C	0.75	46 MB	333	48
1773190083	52 °C	0.52	50 MB	323	48
1773189367	52.6 °C	0.57	47 MB	325	48
1773188642	52.6 °C	0.64	47 MB	332	48
1773187921	52 °C	0.52	46 MB	332	48
1773185050	52.6 °C	0.65	48 MB	328	48
1773184329	52.6 °C	0.47	45 MB	328	48
1773183609	52.6 °C	0.65	48 MB	328	48
1773181447	52.6 °C	0.67	49 MB	311	48
1773180006	52.6 °C	0.25	50 MB	311	48
1773178565	52.6 °C	0.68	50 MB	308	48
1773177124	52 °C	0.7	45 MB	325	48
1773172801	52.6 °C	0.41	47 MB	320	48
1773170650	53.1 °C	0.68	47 MB	312	48
1773169930	52.6 °C	0.68	48 MB	312	48
1773168489	52.6 °C	0.74	49 MB	306	48
1773167768	53.6 °C	0.61	48 MB	305	48
1773167048	53.1 °C	1.01	48 MB	324	48
1773163445	53.6 °C	0.55	48 MB	322	48
1773162725	53.1 °C	0.55	49 MB	322	48
1773161285	53.6 °C	0.68	47 MB	319	48
1773159843	53.6 °C	0.47	49 MB	328	48

*Used Equation Coefficients:

CPU_temp: 0, 0.1, 0

Load: 0, 0.01, 0

Fmem: 0, 1, 0

Nodes[I]: 0, 1, 0

Dests[F]: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)