DG0OPK-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0OPK-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1777026899	26.8 C deg	29.4 %	14.2 C deg
1777025087	26.7 C deg	29.4 %	12.8 C deg
1777023261	26.8 C deg	29.2 %	12.2 C deg
1777021444	26.7 C deg	29 %	11.5 C deg
1777019634	26.6 C deg	28.8 %	10.8 C deg
1777017849	26.6 C deg	28.6 %	9.8 C deg
1777016050	26.6 C deg	28.3 %	8.9 C deg
1777014194	26.5 C deg	27.8 %	8 C deg
1777012466	25.8 C deg	27.5 %	7.1 C deg
1777012365	25.8 C deg	27.5 %	7.1 C deg
1777011238	24.3 C deg	25.8 %	4.2 C deg
1777008843	26.7 C deg	30.5 %	1.5 C deg
1777006974	26.8 C deg	30.6 %	0.5 C deg
1777005134	26.8 C deg	30.7 %	0.2 C deg
1777003345	26.8 C deg	30.7 %	0.2 C deg
1777001480	26.8 C deg	30.8 %	0.5 C deg
1776999659	26.8 C deg	30.7 %	0.4 C deg
1776997885	26.9 C deg	30.7 %	1.1 C deg
1776996070	27 C deg	30.7 %	1.5 C deg
1776994278	27 C deg	30.8 %	1.8 C deg
1776992402	27 C deg	30.8 %	2.1 C deg
1776990590	27.1 C deg	30.8 %	2.6 C deg
1776988787	27.1 C deg	30.8 %	3.2 C deg
1776986958	27.1 C deg	30.9 %	3.7 C deg
1776985152	27.2 C deg	30.7 %	4.1 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)