DG4LD-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG4LD-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1787579261	0 C deg	42.6 %	40 C deg
1787577458	0 C deg	43 %	39.3 C deg
1787575629	0 C deg	43.1 %	38.1 C deg
1787573835	0 C deg	43 %	38.2 C deg
1787572012	0 C deg	43.9 %	36.7 C deg
1787568388	0 C deg	42.6 %	36.8 C deg
1787562919	0 C deg	41.9 %	32.2 C deg
1787561135	0 C deg	41.6 %	32.2 C deg
1787559287	0 C deg	41.6 %	31.5 C deg
1787557478	0 C deg	41.8 %	29 C deg
1787555675	0 C deg	41 %	30.6 C deg
1787553858	0 C deg	41.4 %	24.1 C deg
1787552040	0 C deg	41 %	24.3 C deg
1787550209	0 C deg	41.2 %	22.5 C deg
1787548394	0 C deg	41.2 %	21 C deg
1787546580	0 C deg	41.3 %	19.8 C deg
1787542945	0 C deg	41.3 %	21 C deg
1787541130	0 C deg	41.4 %	21.2 C deg
1787539322	0 C deg	41.3 %	21.8 C deg
1787537502	0 C deg	41.4 %	22.1 C deg
1787535685	0 C deg	41.4 %	22.7 C deg
1787533869	0 C deg	41.5 %	22.3 C deg
1787532053	0 C deg	41.7 %	21.6 C deg
1787530235	0 C deg	41.6 %	21.3 C deg
1787528441	0 C deg	41.7 %	22 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)