DG0UHK-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG0UHK-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp*	Humi*	Baro*
1789937494	14 deg C	67.4 %	1048.2 hPa
1789936599	14.1 deg C	67.1 %	1048.2 hPa
1789935695	14.3 deg C	66.8 %	1048.1 hPa
1789934790	14.5 deg C	66.6 %	1048 hPa
1789933892	14.5 deg C	66.3 %	1047.9 hPa
1789932987	14.6 deg C	65.4 %	1047.7 hPa
1789932087	14.7 deg C	64.2 %	1047.6 hPa
1789931187	14.9 deg C	63.1 %	1047.4 hPa
1789930284	15.2 deg C	62.1 %	1047.2 hPa
1789929382	15.4 deg C	61.2 %	1046.9 hPa
1789928478	15.6 deg C	60.1 %	1046.7 hPa
1789927578	16 deg C	58.9 %	1046.5 hPa
1789926673	16.2 deg C	57.4 %	1046.2 hPa
1789926356	16.4 deg C	56.8 %	1046.1 hPa
1789925454	16.8 deg C	55.1 %	1045.9 hPa
1789924555	17.4 deg C	53.4 %	1045.7 hPa
1789923649	18 deg C	51.6 %	1045.2 hPa
1789922748	18.7 deg C	50 %	1021.1 hPa
1789921844	19.2 deg C	48.8 %	1020.8 hPa
1789920941	20 deg C	45.8 %	1020.2 hPa
1789920043	20.3 deg C	45 %	1019.5 hPa
1789919146	20.3 deg C	44.5 %	1019.2 hPa
1789918243	20.7 deg C	44 %	1019 hPa
1789917345	21.2 deg C	44 %	1018.6 hPa
1789916447	21.6 deg C	45.2 %	1018.5 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)