DF3OT-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DF3OT-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1787589954	20 deg C	58.5 %	1019.3 hPa
1787589054	20.2 deg C	57.7 %	1019.5 hPa
1787588154	20.2 deg C	56.5 %	1019.2 hPa
1787587254	20.4 deg C	57 %	1020.3 hPa
1787586353	20.7 deg C	55.9 %	1019.8 hPa
1787586022	20.7 deg C	56.8 %	1019.9 hPa
1787585121	20.8 deg C	56.1 %	1020.7 hPa
1787584222	20.7 deg C	55.9 %	1020.7 hPa
1787583321	20.9 deg C	55.6 %	1021.3 hPa
1787582421	20.6 deg C	54.8 %	1020.8 hPa
1787581521	20.5 deg C	55 %	1020.7 hPa
1787580621	20.9 deg C	55.1 %	1020.9 hPa
1787579721	19.8 deg C	61.1 %	1021.6 hPa
1787578821	19.8 deg C	60.7 %	1022.3 hPa
1787577921	19.8 deg C	60.7 %	1022 hPa
1787577021	19.6 deg C	62.3 %	1022.2 hPa
1787576120	19.5 deg C	64 %	1021.6 hPa
1787575220	19.3 deg C	63.9 %	1022 hPa
1787574320	19.6 deg C	64.2 %	1021.9 hPa
1787573988	19.5 deg C	64.8 %	1022.9 hPa
1787573088	19.5 deg C	65.4 %	1022.6 hPa
1787572188	19.1 deg C	65.9 %	1022.8 hPa
1787571287	18.7 deg C	66.1 %	1021.8 hPa
1787570387	18.7 deg C	66.5 %	1023.5 hPa
1787569487	18.6 deg C	66.4 %	1024.1 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)