BV1EV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV1EV-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1781709674	38.3 C	7 p	13 p	451 p
1781708474	38.4 C	3 p	10 p	451 p
1781707304	38.4 C	3 p	10 p	451 p
1781706074	38.3 C	4 p	10 p	451 p
1781704874	38.5 C	3 p	10 p	451 p
1781703674	39.6 C	3 p	10 p	451 p
1781702493	38.9 C	4 p	10 p	451 p
1781701274	38.9 C	3 p	10 p	451 p
1781700074	38.6 C	3 p	10 p	451 p
1781698874	39.5 C	4 p	10 p	451 p
1781697674	39.4 C	3 p	10 p	451 p
1781696474	39 C	3 p	10 p	451 p
1781695274	38.8 C	4 p	10 p	451 p
1781694074	39.6 C	3 p	10 p	451 p
1781692874	39.9 C	3 p	12 p	451 p
1781691674	39.9 C	4 p	18 p	451 p
1781690474	39.5 C	5 p	21 p	451 p
1781689274	39.7 C	9 p	19 p	449 p
1781688074	39.6 C	7 p	13 p	443 p
1781686874	39.9 C	3 p	10 p	443 p
1781685674	40.6 C	3 p	10 p	443 p
1781684475	40.5 C	4 p	10 p	443 p
1781683274	40.6 C	3 p	10 p	443 p
1781682074	40.8 C	3 p	10 p	443 p
1781680874	40.2 C	4 p	10 p	443 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)