BV1EV-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV1EV-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1776673065	37.7 C	71 p	222 p	4111 p
1776671865	37.7 C	78 p	231 p	4091 p
1776670665	37.7 C	73 p	238 p	4077 p
1776669465	38 C	79 p	226 p	4147 p
1776668265	36.5 C	85 p	211 p	4183 p
1776667065	37.7 C	61 p	203 p	4232 p
1776665865	36.1 C	65 p	210 p	4294 p
1776664665	35.6 C	77 p	215 p	4367 p
1776663465	36.9 C	68 p	209 p	4423 p
1776662265	35.9 C	70 p	225 p	4471 p
1776661065	36 C	71 p	212 p	4516 p
1776659865	34 C	84 p	196 p	4555 p
1776658664	32.3 C	56 p	180 p	4578 p
1776657465	30.5 C	55 p	237 p	4606 p
1776656265	29.9 C	70 p	269 p	4662 p
1776655064	30.4 C	112 p	270 p	4763 p
1776653865	29.6 C	87 p	207 p	4911 p
1776652665	30.6 C	71 p	156 p	5126 p
1776651465	29.7 C	49 p	130 p	5366 p
1776650264	29.4 C	36 p	144 p	5656 p
1776649065	31 C	45 p	195 p	5800 p
1776647865	29.6 C	63 p	221 p	5888 p
1776646665	30.8 C	87 p	222 p	5936 p
1776645465	31.1 C	71 p	211 p	5972 p
1776644265	30.6 C	64 p	205 p	6025 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)