IU1KBL-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IU1KBL-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1761505063	14.03 Volt	100 Pcnt	40 C
1761503263	14.03 Volt	100 Pcnt	40.5 C
1761501463	14.03 Volt	100 Pcnt	40.5 C
1761497864	14.03 Volt	100 Pcnt	41.5 C
1761496064	14.03 Volt	100 Pcnt	41.5 C
1761494264	14.03 Volt	100 Pcnt	42.5 C
1761492464	14.03 Volt	100 Pcnt	43.5 C
1761490664	14.03 Volt	100 Pcnt	45.5 C
1761488864	14.03 Volt	100 Pcnt	47 C
1761487064	14.03 Volt	100 Pcnt	47.5 C
1761483464	14.03 Volt	100 Pcnt	45.5 C
1761481664	14.03 Volt	100 Pcnt	43 C
1761479864	14.03 Volt	100 Pcnt	42 C
1761476264	14.03 Volt	100 Pcnt	41.5 C
1761474464	14.03 Volt	100 Pcnt	41 C
1761472664	14.03 Volt	100 Pcnt	40.5 C
1761467264	14.03 Volt	100 Pcnt	38 C
1761465464	14.03 Volt	100 Pcnt	37.5 C
1761460064	14.03 Volt	100 Pcnt	37 C
1761458264	14.03 Volt	100 Pcnt	37.5 C
1761454665	14.03 Volt	100 Pcnt	37.5 C
1761452865	14.03 Volt	100 Pcnt	37 C
1761449265	14.03 Volt	100 Pcnt	37.5 C
1761447465	14.03 Volt	100 Pcnt	37.5 C
1761445665	14.03 Volt	100 Pcnt	37 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)