SP9EPW-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9EPW-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*	V_Ext*
1780596078	352 Count	902 Count	264 Count	0 VDC
1780594277	347 Count	890 Count	260 Count	0 VDC
1780590675	335 Count	869 Count	250 Count	0 VDC
1780588874	329 Count	862 Count	245 Count	0 VDC
1780587074	323 Count	851 Count	240 Count	0 VDC
1780583472	311 Count	832 Count	230 Count	0 VDC
1780581671	306 Count	825 Count	226 Count	0 VDC
1780579871	301 Count	817 Count	222 Count	0 VDC
1780578070	295 Count	803 Count	217 Count	0 VDC
1780574476	281 Count	781 Count	209 Count	4 VDC
1780572676	275 Count	759 Count	204 Count	4 VDC
1780570875	270 Count	744 Count	200 Count	4 VDC
1780569074	264 Count	730 Count	195 Count	4 VDC
1780567273	260 Count	724 Count	192 Count	4 VDC
1780565472	257 Count	712 Count	190 Count	4 VDC
1780563672	252 Count	670 Count	186 Count	4 VDC
1780561871	246 Count	656 Count	181 Count	4 VDC
1780560070	241 Count	643 Count	177 Count	4 VDC
1780558269	237 Count	635 Count	174 Count	4 VDC
1780556469	232 Count	621 Count	170 Count	4 VDC
1780552875	221 Count	595 Count	165 Count	4 VDC
1780551074	216 Count	585 Count	161 Count	4 VDC
1780549274	211 Count	572 Count	157 Count	4 VDC
1780547473	207 Count	558 Count	154 Count	4 VDC
1780545672	203 Count	543 Count	151 Count	4 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)