W1DMR-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W1DMR-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1781869466	13.8 Volt	1100 Pkt	85 Pcnt
1781868867	13.8 Volt	1090 Pkt	84 Pcnt
1781868266	13.8 Volt	1100 Pkt	82 Pcnt
1781867666	13.8 Volt	1120 Pkt	82 Pcnt
1781867066	13.8 Volt	1120 Pkt	82 Pcnt
1781866466	13.8 Volt	1040 Pkt	80 Pcnt
1781865867	13.8 Volt	990 Pkt	80 Pcnt
1781865266	13.8 Volt	980 Pkt	81 Pcnt
1781864666	13.8 Volt	940 Pkt	81 Pcnt
1781864066	13.8 Volt	890 Pkt	80 Pcnt
1781863466	13.8 Volt	870 Pkt	78 Pcnt
1781862866	13.8 Volt	880 Pkt	78 Pcnt
1781862266	13.8 Volt	880 Pkt	77 Pcnt
1781861667	13.8 Volt	880 Pkt	77 Pcnt
1781861066	13.8 Volt	880 Pkt	76 Pcnt
1781860466	13.8 Volt	900 Pkt	77 Pcnt
1781859866	13.8 Volt	910 Pkt	78 Pcnt
1781859266	13.8 Volt	910 Pkt	78 Pcnt
1781858666	13.8 Volt	890 Pkt	79 Pcnt
1781858066	13.8 Volt	870 Pkt	79 Pcnt
1781857466	13.8 Volt	900 Pkt	79 Pcnt
1781856866	13.8 Volt	900 Pkt	79 Pcnt
1781856266	13.8 Volt	900 Pkt	76 Pcnt
1781855667	13.8 Volt	930 Pkt	75 Pcnt
1781855066	13.8 Volt	920 Pkt	74 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)