SP6ZWR-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6ZWR-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1784699158	18.9 C	31.3 %	1022.88 hPa
1784698257	18.2 C	31.71 %	1022.25 hPa
1784697356	17.6 C	32.53 %	1023.38 hPa
1784696455	17.2 C	32.55 %	1022 hPa
1784695554	16.9 C	32.45 %	1026 hPa
1784694653	16.8 C	32.95 %	1019.5 hPa
1784693752	16.7 C	32.71 %	1023.63 hPa
1784692851	16.7 C	33.04 %	1020.88 hPa
1784691950	16.8 C	32.62 %	1021.25 hPa
1784691050	16.9 C	32.99 %	1020.13 hPa
1784690148	17.1 C	32.91 %	1022 hPa
1784689247	17.3 C	32.48 %	1021.13 hPa
1784688346	17.6 C	31.96 %	1022 hPa
1784687445	17.9 C	32.42 %	1020.63 hPa
1784686544	18.3 C	31.74 %	1022 hPa
1784685643	18.6 C	31.85 %	1021.5 hPa
1784684742	19 C	31.43 %	1021.25 hPa
1784683841	19.3 C	31.23 %	1019 hPa
1784682940	19.7 C	31.26 %	1017.88 hPa
1784682039	20.1 C	30.74 %	1018.63 hPa
1784681138	20.5 C	30.66 %	1020 hPa
1784679336	21.3 C	30.3 %	1020.38 hPa
1784678435	21.7 C	30.18 %	1023 hPa
1784677534	22.1 C	29.58 %	1021.75 hPa
1784675732	22.9 C	28.99 %	1021 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)