This is the latest recevied telemetry packets stored in our database for station/object DH1OME-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
QNH*
Temp.out*
1777106236
1012.3 hPa
28 C deg
26.5 %
1018.2 hPa
0 C deg
1777104420
1012.2 hPa
27.9 C deg
26.6 %
1018.2 hPa
0 C deg
1777102605
1012.3 hPa
27.8 C deg
26.6 %
1018.3 hPa
0 C deg
1777100790
1012.3 hPa
27.7 C deg
26.7 %
1018.3 hPa
0 C deg
1777098975
1012.3 hPa
27.7 C deg
26.7 %
1018.3 hPa
0 C deg
1777097159
1012.2 hPa
27.7 C deg
26.7 %
1018.2 hPa
0 C deg
1777095344
1012 hPa
27.7 C deg
26.7 %
1018 hPa
0 C deg
1777093529
1011.7 hPa
27.7 C deg
26.7 %
1017.7 hPa
0 C deg
1777091713
1011.7 hPa
27.7 C deg
26.8 %
1017.7 hPa
0 C deg
1777089899
1011.7 hPa
27.7 C deg
26.7 %
1017.7 hPa
0 C deg
1777088083
1011.8 hPa
27.7 C deg
26.7 %
1017.8 hPa
0 C deg
1777086268
1011.9 hPa
27.7 C deg
26.7 %
1017.9 hPa
0 C deg
1777084453
1012.2 hPa
27.7 C deg
26.7 %
1018.2 hPa
0 C deg
1777082638
1012.3 hPa
27.8 C deg
26.7 %
1018.3 hPa
0 C deg
1777080823
1012.3 hPa
27.8 C deg
26.7 %
1018.2 hPa
0 C deg
1777079008
1012.4 hPa
27.8 C deg
26.7 %
1018.4 hPa
0 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
QNH: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)