This is the latest recevied telemetry packets stored in our database for station/object DL4MFH-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
QNH*
Temp.out*
1777698285
971.1 hPa
21.9 C deg
35.5 %
1028 hPa
0 C deg
1777697762
971 hPa
22.2 C deg
36.5 %
1027.9 hPa
0 C deg
1777697279
971 hPa
21.8 C deg
35.6 %
1028 hPa
0 C deg
1777696843
971 hPa
21.5 C deg
36.7 %
1028 hPa
0 C deg
1777695172
971.1 hPa
21.8 C deg
33 %
1028.1 hPa
0 C deg
1777693364
971.1 hPa
21.9 C deg
33 %
1028 hPa
0 C deg
1777687912
971.4 hPa
22.2 C deg
33 %
1028.2 hPa
0 C deg
1777684284
971.7 hPa
22.3 C deg
33 %
1028.5 hPa
0 C deg
1777682466
971.8 hPa
22.4 C deg
33 %
1028.7 hPa
0 C deg
1777680654
971.9 hPa
22.5 C deg
33 %
1028.8 hPa
0 C deg
1777678836
972.2 hPa
22.6 C deg
33 %
1029 hPa
0 C deg
1777669770
972.5 hPa
23.3 C deg
33.4 %
1029.2 hPa
0 C deg
1777666134
972.5 hPa
23.6 C deg
33.5 %
1029.2 hPa
0 C deg
1777664335
972.3 hPa
23.5 C deg
33.6 %
1029 hPa
0 C deg
1777662501
972.2 hPa
23.5 C deg
34 %
1028.9 hPa
0 C deg
1777658878
972 hPa
23.1 C deg
35.3 %
1028.7 hPa
0 C deg
1777657059
971.8 hPa
19.4 C deg
36.2 %
1029.3 hPa
0 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
QNH: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)