SP3MWT-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP3MWT-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	V_Bat*	V_Ext*
1776706419	830 Count	4 VDC	0.14 VDC
1776704620	829 Count	4 VDC	0.14 VDC
1776702813	828 Count	4 VDC	0.14 VDC
1776701011	827 Count	3.98 VDC	0.14 VDC
1776699208	826 Count	4.01 VDC	0.14 VDC
1776697405	825 Count	4.02 VDC	0.14 VDC
1776695635	824 Count	4.02 VDC	0.14 VDC
1776693833	823 Count	4.02 VDC	0.14 VDC
1776692030	822 Count	4.02 VDC	0.14 VDC
1776690227	821 Count	4.02 VDC	0.14 VDC
1776688424	820 Count	4.03 VDC	0.14 VDC
1776686621	819 Count	4.03 VDC	0.14 VDC
1776684818	818 Count	4.03 VDC	0.14 VDC
1776683015	817 Count	4.04 VDC	0.14 VDC
1776681213	816 Count	4.04 VDC	0.14 VDC
1776679410	815 Count	4.04 VDC	0.14 VDC
1776677607	814 Count	4.04 VDC	0.14 VDC
1776675804	813 Count	4.05 VDC	0.14 VDC
1776674035	812 Count	4.05 VDC	0.14 VDC
1776672232	811 Count	4.05 VDC	0.14 VDC
1776670429	810 Count	4.06 VDC	0.14 VDC
1776668627	809 Count	4.06 VDC	0.14 VDC
1776666824	808 Count	4.06 VDC	0.14 VDC
1776665021	807 Count	4.03 VDC	0.14 VDC
1776663218	806 Count	4.07 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)