KK7MLJ-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KK7MLJ-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1773255084	25.1 C	37.5 %	1027.75 hPa
1773235476	20.1 C	38.79 %	1007.75 hPa
1773191718	25.6 C	33.04 %	1023.88 hPa
1773182712	25.3 C	33.91 %	1024.38 hPa
1773173707	25 C	34.05 %	1024 hPa
1773164703	25.4 C	32.43 %	1022.63 hPa
1773155703	25.1 C	32.7 %	1022.5 hPa
1773146694	25.5 C	31.55 %	981.38 hPa
1773140407	25.8 C	31.37 %	997.88 hPa
1773136312	26 C	31.54 %	1020.5 hPa
1773129686	26.4 C	31.61 %	1021 hPa
1773120681	27 C	31.18 %	1015 hPa
1773115072	27.5 C	30.92 %	1020.88 hPa
1773106886	27.7 C	32.31 %	1001.63 hPa
1773100139	28.1 C	29.23 %	1014.88 hPa
1773093229	27.7 C	28.32 %	1018.5 hPa
1773088752	27.8 C	28.31 %	1017.75 hPa
1773079747	26.1 C	28.79 %	1019.63 hPa
1773070743	24.5 C	28.86 %	1020.75 hPa
1773061738	25.7 C	28.23 %	1019.75 hPa
1773052732	26.4 C	27.87 %	1018.25 hPa
1773043729	26.9 C	27.83 %	1019.25 hPa
1773034723	27.5 C	28.17 %	1017.25 hPa
1773025718	28 C	27.97 %	1016 hPa
1773016713	28.4 C	26.26 %	1017 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)