DB0HEI-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0HEI-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1785316037	2 C deg	24.7 %	38.5 C deg
1785314222	2 C deg	24.7 %	38.5 C deg
1785312406	2 C deg	25 %	38.1 C deg
1785310605	2 C deg	24.5 %	38.2 C deg
1785310590	2 C deg	24.5 %	38.2 C deg
1785308805	2 C deg	23.6 %	39.2 C deg
1785308775	2 C deg	23.6 %	39.2 C deg
1785306959	2 C deg	23.6 %	39.3 C deg
1785305143	2 C deg	24.4 %	38.6 C deg
1785303329	2 C deg	25.2 %	37.7 C deg
1785303326	2 C deg	25.2 %	37.7 C deg
1785301532	2 C deg	25.3 %	37.6 C deg
1785301511	2 C deg	25.3 %	37.6 C deg
1785299703	2 C deg	25.3 %	37.6 C deg
1785299696	2 C deg	25.3 %	37.6 C deg
1785297923	2 C deg	25.1 %	37.8 C deg
1785297879	2 C deg	25.1 %	37.8 C deg
1785296086	2 C deg	25 %	38 C deg
1785296064	2 C deg	25 %	38 C deg
1785294287	2 C deg	25.2 %	37.6 C deg
1785294249	2 C deg	25.2 %	37.6 C deg
1785292435	2 C deg	25.1 %	37.6 C deg
1785292432	2 C deg	25.1 %	37.6 C deg
1785290616	2 C deg	25 %	37.6 C deg
1785288801	2 C deg	24.9 %	37.6 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)