DB0XN-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0XN-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1781859529	0 C deg	29.3 %	36.5 C deg
1781857712	0 C deg	29.2 %	36.5 C deg
1781855896	0 C deg	29 %	36.5 C deg
1781854080	0 C deg	29 %	36.5 C deg
1781852263	0 C deg	28.9 %	36.6 C deg
1781850447	0 C deg	29 %	36.5 C deg
1781848665	0 C deg	29 %	36.5 C deg
1781848632	0 C deg	29 %	36.5 C deg
1781846816	0 C deg	29.1 %	36.4 C deg
1781845000	0 C deg	29 %	36.4 C deg
1781843185	0 C deg	28.9 %	36.4 C deg
1781841369	0 C deg	28.9 %	36.4 C deg
1781839553	0 C deg	28.9 %	36.3 C deg
1781837735	0 C deg	28.9 %	36.3 C deg
1781835920	0 C deg	28.9 %	36.2 C deg
1781834105	0 C deg	28.8 %	36.2 C deg
1781832289	0 C deg	28.7 %	36.3 C deg
1781830491	0 C deg	28.6 %	36.3 C deg
1781830473	0 C deg	28.6 %	36.3 C deg
1781828690	0 C deg	28.6 %	36.3 C deg
1781828658	0 C deg	28.6 %	36.3 C deg
1781826881	0 C deg	28.5 %	36.2 C deg
1781826842	0 C deg	28.5 %	36.2 C deg
1781825042	0 C deg	28.5 %	36.2 C deg
1781825027	0 C deg	28.5 %	36.2 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)