IU7URP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IU7URP-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TX*	RX*	Digi*	V_Bat*	V_Ext*
1776452945	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776452244	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776451511	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776449710	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776448706	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776447723	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776446708	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776446558	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776446313	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776445754	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776445186	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776445150	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776445004	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444962	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444746	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444612	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444508	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444416	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444342	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444137	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776444035	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776418242	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776418241	0 Count	0 Count	0 Count	0 VDC	0 VDC
1776418207	0 Count	0 Count	0 Count	0 VDC	0 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)