This is the latest recevied telemetry packets stored in our database for station/object SQ9RHX-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1776413036
0 Count
2 Count
0 Count
0 VDC
0 VDC
1775896713
0 Count
2 Count
0 Count
0 VDC
0 VDC
1775896582
0 Count
2 Count
0 Count
0 VDC
0 VDC
1775893494
0 Count
2 Count
0 Count
0 VDC
0 VDC
1775817613
0 Count
539 Count
0 Count
0 VDC
0 VDC
1775805582
0 Count
539 Count
0 Count
0 VDC
0 VDC
1775803782
0 Count
452 Count
0 Count
0 VDC
0 VDC
1775802848
0 Count
452 Count
0 Count
0 VDC
0 VDC
1775801048
0 Count
379 Count
0 Count
0 VDC
0 VDC
1775799248
0 Count
319 Count
0 Count
0 VDC
0 VDC
1775797448
0 Count
255 Count
0 Count
0 VDC
0 VDC
1775795648
0 Count
140 Count
0 Count
0 VDC
0 VDC
1775793848
0 Count
73 Count
0 Count
0 VDC
0 VDC
1775792047
0 Count
1134 Count
0 Count
0 VDC
0 VDC
1775790247
0 Count
998 Count
0 Count
0 VDC
0 VDC
1775788444
0 Count
932 Count
0 Count
0 VDC
0 VDC
1775786643
0 Count
809 Count
0 Count
0 VDC
0 VDC
1775784843
0 Count
745 Count
0 Count
0 VDC
0 VDC
1775783043
0 Count
682 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)