YE3ESW-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YE3ESW-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp*	Hum*	Pres*
1776674691	27 °C	22 %RH	1006 hPa
1776670900	33 °C	17 %RH	1006 hPa
1776666783	46 °C	21 %RH	1007 hPa
1776562372	36 °C	32 %RH	1011 hPa
1776554691	28 °C	51 %RH	1010 hPa
1776552876	31 °C	45 %RH	1010 hPa
1776552794	30 °C	49 %RH	1010 hPa
1776503594	32 °C	31 %RH	1007 hPa
1776421192	31 °C	38 %RH	1007 hPa
1776420167	32 °C	27 %RH	1007 hPa
1776416519	38 °C	28 %RH	1007 hPa
1776404169	39 °C	19 %RH	1008 hPa
1776404141	39 °C	20 %RH	1008 hPa
1776404050	39 °C	24 %RH	1008 hPa
1776384133	32 °C	36 %RH	1011 hPa
1776335760	33 °C	44 %RH	1008 hPa
1776335390	32 °C	44 %RH	1008 hPa
1776331337	36 °C	34 %RH	1007 hPa
1776320462	45 °C	11 %RH	1008 hPa
1776302239	32 °C	47 %RH	1011 hPa
1776254341	27 °C	23 %RH	1008 hPa
1776252439	33 °C	44 %RH	1008 hPa
1776252391	33 °C	37 %RH	1008 hPa
1776245156	35 °C	23 %RH	1006 hPa
1776213658	30 °C	45 %RH	1010 hPa

*Used Equation Coefficients:

Temp: 0, 1, 0

Hum: 0, 1, 0

Pres: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)