EB1GEM-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EB1GEM-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784708671	13.35 Volt	350 Pkt	82 Pcnt
1784708372	13.35 Volt	350 Pkt	81 Pcnt
1784707772	13.35 Volt	360 Pkt	81 Pcnt
1784707771	13.35 Volt	360 Pkt	81 Pcnt
1784707172	13.35 Volt	340 Pkt	82 Pcnt
1784706871	13.35 Volt	330 Pkt	81 Pcnt
1784706572	13.35 Volt	340 Pkt	83 Pcnt
1784705972	13.35 Volt	330 Pkt	89 Pcnt
1784705971	13.35 Volt	330 Pkt	89 Pcnt
1784705372	13.35 Volt	300 Pkt	93 Pcnt
1784705071	13.35 Volt	300 Pkt	94 Pcnt
1784704772	13.35 Volt	290 Pkt	95 Pcnt
1784704172	13.35 Volt	280 Pkt	96 Pcnt
1784704171	13.35 Volt	280 Pkt	96 Pcnt
1784703572	13.35 Volt	290 Pkt	96 Pcnt
1784703271	13.35 Volt	300 Pkt	97 Pcnt
1784702972	13.35 Volt	290 Pkt	97 Pcnt
1784702372	13.35 Volt	280 Pkt	96 Pcnt
1784702371	13.35 Volt	280 Pkt	96 Pcnt
1784701772	13.35 Volt	270 Pkt	96 Pcnt
1784701471	13.35 Volt	270 Pkt	96 Pcnt
1784700572	13.35 Volt	240 Pkt	97 Pcnt
1784700571	13.35 Volt	240 Pkt	97 Pcnt
1784699972	13.35 Volt	230 Pkt	97 Pcnt
1784699671	13.35 Volt	230 Pkt	97 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)