ED1YAH Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1YAH. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1772621083	13.77	1.93	10.58	56.65	43.71
1772620901	13.77	1.93	10.58	56.93	44.18
1772620720	13.77	1.92	10.43	56.1	43.71
1772620539	13.77	1.92	10.48	55.83	42.77
1772620359	13.77	1.93	10.62	57.2	44.42
1772620178	13.77	1.93	10.48	56.65	44.18
1772619817	13.77	1.93	10.53	56.65	44.42
1772619637	13.77	1.92	10.48	56.38	43.95
1772619457	13.77	1.93	10.58	56.93	43.95
1772619280	13.77	1.93	10.62	56.93	44.18
1772619094	13.77	1.92	10.43	56.1	43.95
1772618914	13.77	1.93	10.53	56.65	44.42
1772618732	13.77	1.93	10.58	57.2	44.42
1772618551	13.77	1.92	10.39	55.83	43.24
1772618370	13.77	1.93	10.58	56.93	44.65
1772618191	13.77	1.93	10.53	56.93	44.42
1772618011	13.77	1.93	10.58	56.65	43.95
1772617829	13.77	1.92	10.39	55.55	42.54
1772617650	13.77	1.92	10.43	56.1	43.71
1772617466	13.77	1.94	10.62	57.48	44.65
1772617286	13.77	1.93	10.58	56.93	43.95
1772617105	13.77	1.93	10.58	56.93	43.95
1772616924	13.77	1.93	10.62	56.93	43.95
1772616748	13.77	1.92	10.48	56.1	43.48
1772616563	13.77	1.94	10.67	57.75	45.12

*Used Equation Coefficients:

Value1: 0, 0.054, 0

Value2: 0, 0.008, 0

Value3: 0, 0.047, 0

Value4: 0, 0.275, 0

Value5: 0, 0.235, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)