2E0UMR-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 2E0UMR-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1776671084	359 Count	14 Count	3.57 VDC
1776669281	358 Count	14 Count	3.58 VDC
1776667478	357 Count	14 Count	3.5 VDC
1776665673	356 Count	14 Count	3.58 VDC
1776663870	355 Count	14 Count	3.59 VDC
1776662107	354 Count	14 Count	3.6 VDC
1776660303	353 Count	14 Count	3.6 VDC
1776658500	352 Count	14 Count	3.61 VDC
1776656696	351 Count	14 Count	3.61 VDC
1776654893	350 Count	14 Count	3.62 VDC
1776653089	349 Count	14 Count	3.62 VDC
1776651286	348 Count	14 Count	3.63 VDC
1776649482	347 Count	14 Count	3.63 VDC
1776647678	346 Count	14 Count	3.64 VDC
1776645875	345 Count	14 Count	3.64 VDC
1776644072	344 Count	14 Count	3.65 VDC
1776642268	343 Count	14 Count	3.65 VDC
1776640505	342 Count	14 Count	3.65 VDC
1776638702	341 Count	14 Count	3.66 VDC
1776636898	340 Count	14 Count	3.66 VDC
1776635095	339 Count	14 Count	3.65 VDC
1776633291	338 Count	14 Count	3.68 VDC
1776631488	337 Count	14 Count	3.69 VDC
1776629685	336 Count	14 Count	3.65 VDC
1776627881	335 Count	14 Count	3.69 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)