N0KM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0KM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RFIn*	RFiGate*	Temp*
1780606437	165 Pkts	156 Pkts	29 C
1780602837	197 Pkts	184 Pkts	28 C
1780599238	307 Pkts	294 Pkts	27 C
1780595638	202 Pkts	193 Pkts	27 C
1780592038	204 Pkts	197 Pkts	26 C
1780586729	177 Pkts	170 Pkts	26 C
1780583129	173 Pkts	165 Pkts	25 C
1780579529	205 Pkts	194 Pkts	25 C
1780575929	198 Pkts	182 Pkts	25 C
1780572329	161 Pkts	149 Pkts	25 C
1780568729	141 Pkts	130 Pkts	26 C
1780565129	157 Pkts	144 Pkts	26 C
1780561529	142 Pkts	131 Pkts	26 C
1780557929	140 Pkts	132 Pkts	26 C
1780554329	106 Pkts	96 Pkts	27 C
1780550729	84 Pkts	73 Pkts	27 C
1780547129	73 Pkts	62 Pkts	27 C
1780543529	81 Pkts	76 Pkts	27 C
1780539930	126 Pkts	115 Pkts	27 C
1780536329	206 Pkts	195 Pkts	28 C
1780532729	157 Pkts	152 Pkts	28 C
1780529129	284 Pkts	274 Pkts	28 C
1780525529	277 Pkts	267 Pkts	28 C
1780521929	228 Pkts	218 Pkts	27 C
1780518329	215 Pkts	204 Pkts	28 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)