LU6EEG-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU6EEG-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*	V_Bat*
1781634237	758 Count	779 Count	569 Count	4.23 VDC
1781633337	755 Count	776 Count	567 Count	4.23 VDC
1781632436	751 Count	772 Count	564 Count	4.22 VDC
1781631535	747 Count	768 Count	561 Count	4.19 VDC
1781630635	743 Count	764 Count	558 Count	4.22 VDC
1781629734	739 Count	760 Count	555 Count	4.24 VDC
1781628834	735 Count	757 Count	552 Count	4.26 VDC
1781627933	731 Count	753 Count	549 Count	4.16 VDC
1781627032	727 Count	749 Count	546 Count	4.25 VDC
1781626132	723 Count	745 Count	543 Count	4.19 VDC
1781625231	719 Count	741 Count	540 Count	4.2 VDC
1781624330	715 Count	738 Count	537 Count	4.23 VDC
1781623430	712 Count	735 Count	535 Count	4.25 VDC
1781622529	708 Count	731 Count	532 Count	4.19 VDC
1781621628	704 Count	727 Count	529 Count	4.17 VDC
1781620728	700 Count	723 Count	526 Count	4.24 VDC
1781619827	696 Count	719 Count	523 Count	4.15 VDC
1781618926	692 Count	715 Count	520 Count	4.16 VDC
1781618026	688 Count	711 Count	517 Count	4.25 VDC
1781617125	684 Count	707 Count	514 Count	4.18 VDC
1781616225	680 Count	703 Count	511 Count	4.16 VDC
1781615324	676 Count	699 Count	508 Count	4.2 VDC
1781614438	672 Count	695 Count	505 Count	4.25 VDC
1781613537	668 Count	691 Count	502 Count	4.26 VDC
1781612637	665 Count	688 Count	500 Count	4.23 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)